Jagal Group is a leading Nigerian conglomerate with operations in the Oil&Gas, Construction and Manufacturing industries. The company has been growing successfully over the past 40 years, and has become a valuable and respected contributor to the development of the country's economy.

Position: Welder Foreman

Prime Responsibilities and duties

• Ability to weld all position of welding such as 3G, 4G, 6G & 6GR on SMAW/FCAW on both plate and pipe.
• Study engineering drawings and blueprints to determine materials requirements and task sequences.
• Welding spare parts in various directions: flat, horizontal, vertical or overhead, etc.;
• Supervising and identifying any fault in operating the equipment or in relation to any material or equipment, then notifying the supervisors;
• Clamping, holding, tack-welding, heat-bending, bolting, or grinding spare parts as necessary to satisfy the technical requirements and create a welded final product;
• Operating other accessory equipments and performing some tasks necessary for welding metal, such as fusing metal segments, using gas tungsten arc, metal arc, flux-cored arc, and other types of welding arcs;
• Examining finish products and spare parts and comparing them with samples to check whether the specifications are met;
• Being in charge of preparing and setting up necessary tools and equipments for welding job such as shielded metal arc, gas metal arc or other welding equipments

Key Internal Interfaces

• Welding Manager
• Fabrication Manger
• Welder and other Staff

The Person

• Relevant trade test(s) and SSCE. Higher qualifications are added advantages.
• 7 years minimum, in major Oil & Gas EPC projects, must possess vast Knowledge in the fabrication industry.
• Safety certificate (general) and other safety certification will be an added advantage.
• Responsible for the execution and application of the HSE procedures within his work area.
• Should have good communication skills and report writing abilities.

Position: Rigging Foreman

Purpose / Role
Responsible to the Rigging Superintendent for the leadership and organization of the rigging and moving loads function on the site/installation to fully execute the requirements of the rigging and moving loads support service safely and effectively Key aims and objectives.

Prime Responsibilities and duties

• Accountable for promoting Safety.
• Plan & control work activities ensuring that a safe system of work is in place and followed during all lifting operations
• Implement all applicable company / project policies, working practices and procedures, ensuring at all times that the rigging work scope is completed efficiently, in compliance with LOLER and to a high standard of safety.
• Review and approve all lift plans developed by the site/installation rigging and moving loads function .
• Complete all work scopes in accordance with applicable workpack / jobcard instructions, associated procedures and drawings / sketches.
• Ensure job cards are completed and accurate progress reported
• Ensure time writing for the rigging and moving loads function is accurate and completed on time.

The Person

• 5-8 years’ experience in rigging in Oil & Gas / Fabrication environment.
• Previous Offshore Rigger experience is essential
• Level 3 Rigging Assessment or equivalent certification is preferred.
• Good level of verbal and written communication in English.

Position: Scaffolding Foreman

Personnel reporting directly to this position

• Scaffolders

Purpose

• The scaffolding foreman is a working foreman
• Make sure the JSA,S and toolbox talks have been done correctly and are in place
• Make sure the scaffolders are working safely and to the right standards and procedures

Key aims and objectives

• Safety of all personnel
• Lead  scaffold  team  to erect  dismantle modify  all types  of scaffolding

Prime Responsibilities and Duties

• Make sure the work face is kept clean and tidy
• Look with supervisor where scaffold needs erecting decide what materials will be needed arrange for forklift to bring materials from scaffold yard

Other Duties

• Make sure all his team are wearing the correct ppe

Reports

• Reports any issues he has to supervisor / superintendent

Key Internal Interfaces

• Scaffolding team
• Scaffold Manager
• Superintendent

The Person

• 5+ years’ experience
• Be able to lead scaffold team
• Be able to erect dismantle modify all types of scaffolds tube and fittings and system to British standards BSEN12811-1

Position: Pipe Fitter

Qualification

• Relevant trade test(s) and SSCE. Higher qualifications are added advantages.

Prime Responsibilities

• Trade Test Certification. 1&2 labour & productivity or Engineering background.
• Years of Experience. 4years and above.
• Good safety practices i.e.  Understanding of HSE.
• Ability to read and interprete isometric drawings, P & IDS.
• Ability to understand and interpret simple and complex pipe fabrication drawing
• Conversant with abbreviations, signs & codes.
• Ability to identify fittings & materials.
• Marking out and layout of drawings.
• Good understanding of piping spools orientation, elevations, co-ordinates & piping copping.
• Ability to take measurements, do conversions, plates & piping calculations.
• Bending of Isometric directions, preparation of plates & piping length of bevelled.
• Use of grinding machine & burning set.
• Must understand tools and equipment management.
• Must have good attitude and behaviour.
• Ability to use all fabrication /Fitting equipment and instrument
• Awareness of safety rules and standard of the industry.

Experience

• 5- 8 years minimum working experience in the fabrication field.
• Must have worked on a Pipe erection project.
• Working experience on an EPC project will be an additional advantage

Position: Welding Supervisor

Prime Responsibilities and duties

• Ability to weld all position of welding such as 3G, 4G, 6G & 6GR on SMAW/FCAW on both plate and pipe.
• Study engineering drawings and blueprints to determine materials requirements and task sequences.
• Welding spare parts in various directions: flat, horizontal, vertical or overhead, etc.;
• Supervising and identifying any fault in operating the equipment or in relation to any material or equipment, then notifying the supervisors;
• Clamping, holding, tack-welding, heat-bending, bolting, or grinding spare parts as necessary to satisfy the technical requirements and create a welded final product;
• Operating other accessory equipments and performing some tasks necessary for welding metal, such as fusing metal segments, using gas tungsten arc, metal arc, flux-cored arc, and other types of welding arcs;
• Examining finish products and spare parts and comparing them with samples to check whether the specifications are met;
• Being in charge of preparing and setting up necessary tools and equipments for welding job such as shielded metal arc, gas metal arc or other welding equipments

Key Internal Interfaces

• Welding Manager
• Fabrication Manger
• Welder and other Staff

The Person

• Relevant trade test(s) and SSCE. Higher qualifications are added advantages.
• 10 years minimum, in major Oil & Gas EPC projects, must possess vast Knowledge in the fabrication industry.
• Responsible for the execution and application of the HSE procedures within his work area.
• Should have good communication skills and report writing abilities.
• Should have vase experience in fitting with good supervisory qualities.
• Safety certificate (general) and other safety certification will be an added advantage.

Position: Rigging Supervisor

Prime Responsibilities and Duties

· Knowledge of trade terminology (i.e. lifting equipment, lifting accessories, slings, shackles, wires, ropes, chains, cables, nets etc.).
· The incumbent will make sure that gears for a lifting is conveyed to work site; and reporting of any defective rigging gear to Supervisor.
· Knowledge of types and layout of drawings such as structural, layout, plant, equipment detail drawings etc.
· Knowledge of abbreviations and drafting symbols such as lines, piping and fitting symbols, and control symbols commonly used.
· Have the ability to recognize types of lifting equipment (i.e. wire rope hoists, beam clamps, beam trolleys, plate clamps, sheave blocks, winches etc.).
· Have the ability to recognize types of lifting accessories (i.e. slings, shackles, wires, ropes, chains, cables, nets etc.).
· Have knowledge and ability to determine if lifting equipment and lifting accessories are safe to use.
· Have the ability to read and interpret, prepare and sign safety documents (i.e. PTW, Hazard Identification and Risk Assessment (HIRA), Lifting Risk Assessment (TRA) etc.).
· Have the ability to store and assemble lifting equipment and lifting accessories in a safe location
· Ability to report effectively to his superior/higher authority of any case of defective gears.

Key Internal Interfaces

· Rigging Manager
· Fabrication Manger
· Rigger and other Staff

The Person

· Relevant trade test(s) and SSCE. Higher qualifications are added advantages.
· Must possess a Rigging Certificate from a certified professional body.
· Working experience on an EPC project will be an additional advantage
· 7 years’ experience in major Oil & Gas EPC projects must possess vast Knowledge in the fabrication industry. 
· Safety certificate (general) and other safety certification will be an added advantage.
· Responsible for the execution and application of the HSE procedures within his work area.
· Should have good communication skills and report writing abilities.
· Should have vase experience in fitting with good supervisory qualities

Position: Scaffold Supervisor

Purpose

• Manage and coordinate the erection / dismantling / modification of all types of scaffolding to bsen12811-1 standard
• Be conversant with traditional tube and fitting and system scaffolding
• Show Forman scaffolder the task and make sure he has his jsa and toolbox talk in place

Key aims and objectives

• Meet with supervisors from other trades to discuss where scaffolds need erecting
• Arrange for the correct materials to be brought to the work face to complete the task
• Safety of all personel

Prime Responsibilities and Duties

• Make sure the correct use of harnesses and correct working at height procedure sg410 are being applied
• Ensure work areas are maintained in a clean and orderly manor
• Identify stop and immediately correct unsafe acts or conditions

The Person

• 10+ years’ experience
• Have an affinity to work at heights
• Be able to prepare jsa,and toolboxtalks

Position: Structural Fitter - 1

Qualification

• Relevant trade test(s) and SSCE. Higher qualifications are added advantages.

Prime Responsibilities

• 5- 8 years minimum working experience in the fabrication field.
• Trade Test Certification. 1&2 labour & productivity or Engineering background.
• Good safety practices i.e.  Understanding of HSE.
• Conversant with abbreviations, signs & codes.
• Ability to identify fittings & materials.
• Ability to understand and interpret simple and complex structural fabrication drawing.
• Ability to use all fabrication /Fitting equipment and instrument
• Must understand tools and equipment management.
• Awareness of safety rules and standard of the industry.

Experience

• 5- 8 years minimum working experience in the fabrication field.
• Must have worked on a structural fitting   project.
• Working experience on an EPC project will be an additional advantage

Position:Coating Foreman

Purpose
To be a team player in the corrosion protection treatment process of Fabricated Structural Steel Structures and Associated items.

Key aims and objectives

• To apply your work skills in a manner which enables the Coating Department to deliver defect free product, which conforms to customer supplied specifications and Project working procedures.
• To assist the department in achieving this objective at the first attempt, within the time allowed and at each subsequent attempt.

Prime Responsibilities and Duties

• To ensure that your workers carry out tasks in an efficient manner, with all necessary consumables on hand.
• To work with your team and to be able to delegate tasks with authority and in a clear manner.
• To report all faulty equipment and take the necessary action in either fixing it or making sure that the item gets replaced if it is not repairable.
• To follow up on the progress and completion of  tasks delegated to members of your team.
• You will always assume full responsibility for all work under your control.
• The following will be expected of you while you are in the employ of Nigerdock PLC FZE
• To take responsibility for the satisfactory execution of all work instructions issued to the workers in your team.
• To issue these instructions clearly and to ensure they are well understood.
• To ensure all work is executed according to the requirements of project and/or Nigerdock supplied working instructions.
• To ensure that you have read and fully understand the contents of the relevant working procedures, enabling you to ensure the desired  level of quality is attained .
• To ensure that you and the workers under you wear the correct level of PPE and that they work in a safe environment, utilizing correctly maintained equipment and tools.
• To pre- plan your teams work and assist the individuals in planning the execution of their instructed tasks.
• To ensure and if necessary teach your team to work as a competent unit, always taking into account the safety of others working adjacent to your work area.
• To ensure that each individual executes work tasks in accordance with the requirements of the stipulated working procedure.
• To always ensure a JSA has been conducted for the proposed work and that all actions stated ate obeyed.
• To always conduct a job specific toolbox talk with your team, identifying the work hazards prior to entering the work area.
• To set an example to those working below you.

Other Duties
When not performing your primary function as a Foreman, you are expected to take part in any other activities associated with the functioning of the department.